go558a83nk

sorry for AirVPN and sorry for the corruption in Ukraine.

sorry about that, I didn't read carefully enough your original post. I don't know what the problem could be.

can only do so much and not be a hermit with zero technology. I run the whole house through VPN but not much else. there's plenty of me out there in social media, etc.

I've had a good experience with localbitcoins.com

your ISP may be throttling openvpn traffic even though they are "OK" with it.

not sure what DNS settings stock has for openvpn clients. but just make sure it's using Air DNS or else microrouting will not work. in merlin firmware there are options for DNS. you would want to use "exclusive" so that only Air DNS is used.

no, the AC68 can do about 50mbit/s. I have one, overclocked to 1200mhz, so I know.

you must forward ports in the router since you are using the router as your openvpn client. https://airvpn.org/topic/9270-how-to-forward-ports-in-dd-wrt-tomato-with-iptables/

the reason for the ping spikes is that SSL tunnel means a TCP tunnel. TCP packes have a proper order while UDP packets can be received out of order. this is my rudimentary understanding of the root cause. if correct, it makes sense to me that in heavy traffic it will be a TCP connection that's disrupted more (than UDP) because it's more sensitive to any problem.

growing and it's obviously needed. Looking at server status right now and it seems Canada and the Netherlands are slammed.

it's quite common for ISPs to throttle openvpn and will be more common in the future. and like I said it may depend on the route. ISPs negotiate routing onto the different networks thus not all network traversal is equal.

try some other servers. your ISP transit/peering to Metallah may only allow for slow speeds. I know with my ISP most routes seem subject to throttling but a few are wide open. maybe you were/are lucky with the Chicago servers.

the latest versions of stock (and Merlin) Asus firmware put the certs and keys from openvpn configs into jffs to free up nvram. make sure your firmware is current. A factory reset might be needed if you continue to have problems or after a firmware update since many things change.

Hi staff, just wondering about the development plans for Eddie. Specifically, I'm wondering when Eddie will be ready to support other VPN provider configs. I've seen you mention that support for all ovpn configs was one of your goals. Thanks.

I would install Kodi and some addons such as phoenix, genesis, and more.

Yes, I think you can make this work quite well though it takes a little configuration and trial and error. I do think you will need to spend more money than you project to buy a router with powerful enough CPU to suit your needs. Did you have one in mind? Also, when you are forwarding ports you'll need to follow the below instructions no matter what router firmware you actually end up using. It's all just a linux box in the end. https://airvpn.org/topic/9270-how-to-forward-ports-in-dd-wrt-tomato-with-iptables/

just look at the openvpn log, it says what cipher is used.

it sounds like you need to decide just how anonymous and private you want to be. if you want to head down that road ditch your iphone and get a burn phone, paid with cash.

thanks. had to upgrade my openvpn version (Linux Mint 17.2).

it's difficult to get a pre-paid visa that's anonymous. obviously pay with cash, but some still require personal information to activate. Eddie is AirVPN's openvpn GUI that's quite powerful. If setup properly it will prevent DNS leaks and has a kill switch.

Air uses 4096 bit. Elliptical curve may be better for the current hot topic vulnerability but only if you use ellipses that were not tampered with by the NSA to allow them a back door.

I'm confused by the different unit usage - megabit or gigabyte, which is it?

stunnel is what you need to run SSL tunnel.

You are right, it uses only one CPU instead of two!!! What do you mean with OpenVPN client switching? There is only one in the router? Can you provide me with more info about taskset? I hope you don't mean PPTP or L2TP as I don't want to use these protocols for security reasons! no, I do not mean PPTP or L2TP. not sure what the stock firmware looks like but firmware 378.55 Merlin firmware has two openvpn clients. just select which client you use in the GUI. you can search the web for how to use taskset.

to run with SSH tunnel you just need to be able to run shell scripts and have openssh installed. I don't know if dd-wrt can do this stock or if you need to install something like entware to gain access to more apps. you should ask on a dd-wrt message board