Jump to content
Not connected, Your IP: 3.145.55.48
BitWanderer

High packet loss on server Ancha (The Netherlands)

Recommended Posts

On server Ancha (The Netherlands) i have a lot of packet loss (> 50%) since a couple of hours.
The connection to my ISP is fine so it looks like the problem is not on my end.

Share this post


Link to post
5 hours ago, blancken said:

The connection to my ISP is fine so it looks like the problem is not on my end.


Well, probably wrong.
https://airvpn.org/servers/Ancha/
No packet loss reports in the last 24 hours. Definitely something on your end.

NOT AN AIRVPN TEAM MEMBER. USE TICKETS FOR PROFESSIONAL SUPPORT.

LZ1's New User Guide to AirVPN « Plenty of stuff for advanced users, too!

Want to contact me directly? All relevant methods are on my About me page.

Share this post


Link to post
Posted ... (edited)
19 hours ago, OpenSourcerer said:

Well, probably wrong.
https://airvpn.org/servers/Ancha/
No packet loss reports in the last 24 hours. Definitely something on your end.

I'm not sure: Rebooted all network devices, though everything was stable except the VPN connection to Ancha.
ISP connection is OK, no hiccups or loss or slowness whatsoever. Speed test shows full speed.
Tested with server Alcyone, all OK, zero packet loss.

Moreover, traceroute indicates a problem with Ancha:

|------------------------------------------------------------------------------------------|
|                                      WinMTR statistics                                   |
|                       Host              -   %  | Sent | Recv | Best | Avrg | Wrst | Last |
|------------------------------------------------|------|------|------|------|------|------|
|                            172.29.230.1 -    0 |  352 |  352 |    0 |   10 | 1329 |    1 |
|                           192.168.100.1 -    0 |  352 |  352 |    0 |   10 | 1330 |    1 |
|                            xxx.xxx.xxx.xxx -    0 |  352 |  352 |    6 |   18 | 1315 |   11 |
|                           xxx.xxx.xxx.xxx -    0 |  352 |  352 |    5 |   20 | 1315 |    6 |
|                           xxx.xxx.xxx.xxx -    0 |  352 |  352 |    6 |   16 | 1315 |   16 |
|                          80.249.212.159 -    0 |  352 |  352 |    6 |   17 | 1317 |   11 |
|                           37.123.210.79 -    1 |  301 |  300 |   15 |  524 | 4621 |  137 |
|                         213.152.162.167 -   17 |  217 |  182 |    0 |   45 | 2109 |   32 |
|________________________________________________|______|______|______|______|______|______|
   WinMTR v0.92 GPL V2 Edited ... by OpenSourcerer
Slight edit to remove something felt like advertising

Share this post


Link to post

What I can confirm from my end:

$ sudo traceroute -T ancha.airvpn.org
traceroute to ancha.airvpn.org (213.152.162.164), 30 hops max, 60 byte packets
1  _gateway (192.168.110.1)  1.226 ms  1.583 ms  1.894 ms
2  p3e9bf2fc.dip0.t-ipconnect.de (62.155.242.252)  12.224 ms  12.310 ms  12.401 ms
3  217.5.116.86 (217.5.116.86)  17.824 ms  17.996 ms  18.572 ms
4  80.156.162.158 (80.156.162.158)  18.122 ms  18.220 ms  18.314 ms
5  ae5-2074.ams10.core-backbone.com (81.95.2.138)  22.808 ms  23.744 ms  25.571 ms
6  core-backbone.global-layer.com (80.255.15.206)  31.128 ms  29.985 ms  30.050 ms
7  37.123.210.79 (37.123.210.79)  190.199 ms  132.735 ms  183.054 ms
8  164.162.152.213.in-addr.arpa (213.152.162.164)  26.676 ms  25.597 ms  26.816 ms

A bit high for that nameless router there. Similar for you, 137 ms. Maybe the problem is there.

NOT AN AIRVPN TEAM MEMBER. USE TICKETS FOR PROFESSIONAL SUPPORT.

LZ1's New User Guide to AirVPN « Plenty of stuff for advanced users, too!

Want to contact me directly? All relevant methods are on my About me page.

Share this post


Link to post
22 hours ago, OpenSourcerer said:

What I can confirm from my end:

$ sudo traceroute -T ancha.airvpn.org
traceroute to ancha.airvpn.org (213.152.162.164), 30 hops max, 60 byte packets
1  _gateway (192.168.110.1)  1.226 ms  1.583 ms  1.894 ms
2  p3e9bf2fc.dip0.t-ipconnect.de (62.155.242.252)  12.224 ms  12.310 ms  12.401 ms
3  217.5.116.86 (217.5.116.86)  17.824 ms  17.996 ms  18.572 ms
4  80.156.162.158 (80.156.162.158)  18.122 ms  18.220 ms  18.314 ms
5  ae5-2074.ams10.core-backbone.com (81.95.2.138)  22.808 ms  23.744 ms  25.571 ms
6  core-backbone.global-layer.com (80.255.15.206)  31.128 ms  29.985 ms  30.050 ms
7  37.123.210.79 (37.123.210.79)  190.199 ms  132.735 ms  183.054 ms
8  164.162.152.213.in-addr.arpa (213.152.162.164)  26.676 ms  25.597 ms  26.816 ms

A bit high for that nameless router there. Similar for you, 137 ms. Maybe the problem is there.

Its normal for router to not answer to ICMP packets with high priority, nothing to worry about.
ICMP is send to routing-engine while fowarding is done in asic hardware. As long as the target has normal ping / no loss, thats nothing to be conserned about.

However, the initial trace of blancken shows loss at the target, which indicates loss on the back-route from server --> home dsl, or maybe the server itself, hard to tell without any conrect traceroutes from both sides to multiple targets within  both destinations.

 

Share this post


Link to post
2 hours ago, arteryshelby said:

Its normal for router to not answer to ICMP packets with high priority, nothing to worry about.


Be advised of the -T switch to traceroute.

-T, --tcp
             Use TCP SYN for probes


If a router needs 150 ms on average to answer to TCP connections, this is something to be aware of. I've given up using ICMP for traceroutes because of the relatively high block rate. Some hops in between simply don't answer.

NOT AN AIRVPN TEAM MEMBER. USE TICKETS FOR PROFESSIONAL SUPPORT.

LZ1's New User Guide to AirVPN « Plenty of stuff for advanced users, too!

Want to contact me directly? All relevant methods are on my About me page.

Share this post


Link to post
23 minutes ago, OpenSourcerer said:

Be advised of the -T switch to traceroute.

-T, --tcp
             Use TCP SYN for probes


If a router needs 150 ms on average to answer to TCP connections, this is something to be aware of. I've given up using ICMP for traceroutes because of the relatively high block rate. Some hops in between simply don't answer.

Keep in mind that the same principial applies, router answer every packet directly send to the router (e.g. not forwarding) in software by the cpu. It does not matter if you use ICMP/UDP or TCP in a traceroute for this. So the same high latency) might be observed.
 

Share this post


Link to post

Of course, I never denied it. But I reject your shrugged-off "nothing to worry about". There does seem to be a connectivity bottleneck if a connection must be IGPed through Liberty Global's backbone. If I do these tests with other servers, most of which take a route through Cogent, no problem.


NOT AN AIRVPN TEAM MEMBER. USE TICKETS FOR PROFESSIONAL SUPPORT.

LZ1's New User Guide to AirVPN « Plenty of stuff for advanced users, too!

Want to contact me directly? All relevant methods are on my About me page.

Share this post


Link to post

My input was just taking your traceroutes into consideration.
The original trace shows indeed loss on the target which might high server load or something else.

All i said was that the internal gateway of global layer (i think you mixed up global layer and liberty global?) 37.123.210.79 (37.123.210.79)  190.199 ms  132.735 ms  183.054 ms
is nothing to be conserned about in general.

So "nothing to worry about" just referenced to router answering UDP/ICMP/TCP packet for traceroute, not the initial problem - might have come accros wrong :)

 

Quote
A bit high for that nameless router there. Similar for you, 137 ms. Maybe the problem is there.

Share this post


Link to post

The next morning it seemed the packet loss was gone, but later that day it came back.
Ancha was just not stable. So I switched to the server Merga and we are on 0% packet loss since.

There was definitively something wrong with Ancha, but after changing server it works for me.

Share this post


Link to post

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
  • Security Check
    Play CAPTCHA Audio
    Refresh Image

×
×
  • Create New...